Product Info
The TimeCutter SS 5000 Riding Mower is a ride-on, rotary-blade lawn mower intended to be used by homeowners in residential applications. It is primarily designed for cutting grass on well-maintained lawns.
Preventive Maintenance Schedule
Before Storage:
- Perform all maintenance procedures listed above before storage
- Paint any chipped surfaces
Daily:
- Clean the air intake screen
- Inspect the blades
- Inspect the grass deflector for damage
After Each Use:
- Clean the mower-deck housing
- Grease all lubrication points
- Clean the air-cleaner foam element (more often in dusty, dirty conditions)
Every 200 Hours:
- Replace the spark plug(s)
- Replace the in-line fuel filter
- Charge the battery and disconnect the battery cables
Every 25 Hours:
- Check tire pressure
- Check the belts for wear or cracks
- Replace the air-cleaner foam element (more often in dusty, dirty conditions)
- Service the air-cleaner paper element (more often in dusty, dirty conditions)
- Change the engine oil (more often in dusty, dirty conditions)
Every 100 Hours:
- Change the oil filter (more often in dusty, dirty conditions)
- Check the spark plug(s)
- Check the in-line fuel filter
- Replace the air-cleaner paper element (more often in dusty, dirty conditions)
Parts List
- Blade: Cutting blade for the mower deck (Part Number: Not Available)
- Mower Belt: Drive belt for the mower deck (Part Number: Not Available)
- Air Filter: Air cleaner for the engine (Part Number: Not Available)
- Spark Plug: Ignition spark plug for the engine (Part Number: Not Available)
- Fuel Filter: In-line fuel filter (Part Number: Not Available)
- Battery: 12V battery for the electrical system (Part Number: Not Available)
Product Specs Sheet
- Engine: Kawasaki, Kohler, or Toro engine
- Fuel Tank Capacity: Not specified
- Cutting Width: Not specified
- Height of Cut: Adjustable from 38 mm (1-1/2 inches) to 115 mm (4-1/2 inches)
- Tire Size: Front: Not specified, Rear: Not specified
Troubleshooting
- The engine overheats:
- Reduce the ground speed
- Add oil to the crankcase
- Remove the obstruction from the cooling fins and air passages
- Clean or replace the air-cleaner element
- Contact an Authorized Service Dealer
- The starter does not crank:
- Move the blade-control switch to Disengaged
- Move the motion-control levers outward to the PARK position
- Charge the battery
- Check the electrical connections for good contact
- Replace the fuse
- Contact an Authorized Service Dealer
- The engine does not start, starts hard, or fails to keep running:
- Fill the fuel tank
- Clean or replace the air-cleaner element
- Install the wire(s) on the spark plug
- Install a new, correctly gapped spark plug(s)
- Replace the fuel filter
- Contact an Authorized Service Dealer
- Drain the tank and replace the fuel with the proper type
- Add oil to the crankcase
- The machine does not drive:
- Close the tow valves
- Contact an Authorized Service Dealer
- There is an abnormal vibration:
- Tighten the engine-mounting bolts
- Tighten the appropriate pulley
- Contact an Authorized Service Dealer
- Install a new cutting blade(s)
- Tighten the blade-mounting bolt
- Contact an Authorized Service Dealer
- The cutting height is uneven:
- Sharpen the blade(s)
- Install a new cutting blade(s)
- Level the mower from side-to-side and front-to-rear
- Adjust the anti-scalp wheel height
- Clean the underside of the mower
- Adjust the tire pressure
- Contact an Authorized Service Dealer
- The blades do not rotate:
- Install a new drive belt
- Install the drive belt and check the adjusting shafts and belt guides for the correct position
- Contact an Authorized Service Dealer
- Install a new mower belt
Please
note that any procedure, checklist, or other document available on Limble is provided for general education and
information only and does not constitute legal, medical, or financial advice. Limble makes the materials available
AS IS and AS PROVIDED, without warranties of any kind. By downloading or using any such materials, you assume the
risk that they may not be appropriate for your specific situation and agree that you are solely responsible for any
such use, including compliance with applicable law and with meeting any conditions of product warranties. It is
recommended to contact OEM for the most accurate information.
a30b9d99-f8d1-4f96-bf9f-16a8f467ebc0
Configure and custumize to fit your needs
-
Increase Productivity
Prioritize and complete work orders faster with efficient, collaborative software your team will love using.
-
Reduce Downtime
Avoid setbacks with a proactive, preventive maintenance strategy and move fast when emergencies do happen.
-
World Class Support
Limble’s support team is ready to answer any questions you have in 60 seconds or less, 24/7.
Want to see Limble in Action?
FAQs
Why are Standard Operating Procedures (SOP) Important?
SOPs ensure consistency, efficiency, and safety by providing clear guidelines for tasks. They streamline training, maintain quality, ensure compliance, and support continuous improvement and accountability.
What is CMMS?
CMMS stands for Computerized Maintenance Management System. CMMS software helps businesses manage, automate, and streamline all of their maintenance operations.
Is Limble’s CMMS Mobile Friendly?
Limble is consistently rated Easiest-to-Use CMMS on review sites like G2, Capterra, and Software Advice. And our customers agree. With our mobile CMMS app, teams experience 30%+ better productivity, on average, requiring little to no training or ramp-up time. Our CMMS app can travel with your team, no matter where they go! Visit our App Store or Google Play for more information.
Integration
Limble provides seamless, pre-built CMMS Integrations with the most widely used software systems. That means no help from a developer or your IT team is required. Learn more about our integrations.
Security
At Limble, our world-class data security practices ensure your account information is safe. We use state-of-the-art technologies and industry best practices to maintain a secure infrastructure, including SOC-II Type II certification, regular penetration testing, and continuous security training for our staff.